How well do you know your GTE???

[sb_scottmonkey]

Some of you may remember this from MIG... but for those who don't.. lets play.. NAME THAT BOLT!! :) hehee...

http://img.photobucket.com/albums/v323/sb_scottmonkey/sadstate.jpg

Scott :D

[Matheusc20xe]

lol.. really mess! in this pack have the battery bracket and the alternator mounting..only things that i know.. :confused: :)

[Jon S]

how much for the wing bolt . lol

[Kris]

Battery clamp and the top mounts for the radiator

[DarrenH]

cracks typing fingers, and gives them a warm up wiggle....

:D

[Tom]

LOL I remember this off MIG !

Think I can name a few , brake servo bolts, seat frame bolts, and what looks like some used CV boot clips.:)

[_SBD16v]

tbh i doubt there would be much i would not know but the pics fuzzy so i cannot see putup a bettr pic and i will tell you loads of them

[Kris]

Im shure there is a couple of the nuts that attach the steering colom to the bulkhead

[Xedrah]

Together we will probably be able to fix your Astra. lol :)

[_SBD16v]

is no one else see they pic very blury

[Gander]

is no one else see they pic very blury
Too much self abuse Rob?

Large rubber bungs ar for the radiator mounts. The rubber with the two holes is a brake line grommet. Theres a few seat bolts, interior screws, wing bolts, oil cooler line support, door light contact and...
NERD ALERT
Im sure the upside down thing in the top right hand corner is the contact plate for the bootlid electrics:o

[_SBD16v]

no seriously i cannot see any of it shit some one send it to me on msn

[_SBD16v]

nost have been mentioned but i can see one that deff aint gear linkage pin

[DarrenH]

NERD ALERT
Im sure the upside down thing in the top right hand corner is the contact plate for the bootlid electrics:o

even nerdier if you can suggest the real use for those zip ties. (which are actual factory fitted GM ones if i'm not mistaken)

[Brett]

Theres a shiney bolt near one of the red monuts, thats the one thats holds the centre console to the bottom of the dash below the ashtray and heater controls.

I think the gold ones could be the two locating bolts for the front struts you can also use to bolt a strut brace on

the pin that basically top centre, is that for the door hinges? Ive got one in the garage for sure.

I can also deffinalty make out the screws with a really fine thread that screw the grab handles to the roof, other screws I can identify are the flat toped ones that are part of the fascia - they little plastic covers that pop into the top, the ones that hold the plastic sill covers on, larghe headed ones that hold the entire dash together

think I can see an airbox bolt too...

[sb_scottmonkey]

lol, the pinn in top centre is for the brake-pedal-to-servo joint.

Odders, those are original GM cable ties, i know what they're for, but not saying! lol... :)

Shiny nuts referered to aren't suspension top mounts, but are for the pedal tray mounting.

And yes, It's Not a Metit, there is a steering columb bolt in there!

lol.. it get to a certian state doesn't it! lol.. :)

[_SBD16v]

this is good

[DarrenH]

Odders, those are original GM cable ties, i know what they're for, but not saying! lol... :)

well i'm sure they are used on the filler neck and breather hoses for the fuel tank. but as everything else in the box is from the engine bay/front of the car, the smart money is on the ones used around the macpherson struts.

[sb_scottmonkey]

lol.. it was a non ABS car! but yes they are from the filler neck. Good work!

[Jon S]

WE Could have a little game going here :p

http://www.gameshow-galaxy.net/images/DzlItem240.jpghttp://img112.exs.cx/img112/4584/SSDG.jpg

[Kris]

The door contact switch for the interior light and i think i spy one of the spline top screws used for the back seats ?.

[Gander]

well i'm sure they are used on the filler neck and breather hoses for the fuel tank
Aww no fair, I knew that:p

[sb_scottmonkey]

The bits came from all over thecar.. not just engine bay. Should have said! lol

[traffman]

half of those pieces in the box are missing from my car, the old circlip principle is to blame for that.

usually when i bolt something back on the car i end up with a few spare bolts.